1 / 5
New Screw Separator ZSP-800 5.5 kW

New Screw Separator ZSP-800 5.5 kW

The ZSP-800 screw separator processes liquid manure, digestate and organic slurries at a nominal throughput of 25–45 m³/h. It combines a 5.5 kW drive with a larger screening area for higher feed volumes.

The ZSP-800 has a 550 mm main screening section and an additional 250 mm section. Compared with the ZSP-550, the upper nominal throughput increases from 35 to 45 m³/h with the same motor power. Overall machine length is 2,335 mm.

Separation performance

Dry matter in the separated solid fraction is 25–30%. Nominal throughput is 25–45 m³/h. Flow and dewatering depend on the feed composition and solids content, the screen slot width and the counterweight settings. These parameters determine the balance between throughput and dewatering.

Operating principle

Premixed slurry enters the working chamber. The rotating screw moves the material along a cylindrical screen, allowing liquid to pass through its slots. Retained solids move towards the outlet, where they are compressed and dewatered before leaving as a separate stream.

Outlet resistance is adjusted using counterweighted arms. This mechanical adjustment allows the dewatering level to be set on site. An even supply of previously homogenised feed helps maintain stable operation.

Working components

The housing is carbon steel. Internal components and the screen are AISI 304 stainless steel. Screen diameter is 261 mm; screening section lengths are 550 + 250 mm. The installed screen has a slot width of 1.0 mm.

The stainless-steel screw has a wear-resistant working surface. Carbide and tungsten coatings are available as options. Replaceable screens allow worn elements to be renewed or a different slot width to be selected. Standard or reinforced screens are used to suit the application.

Applications

At biogas plants, the separator processes digestate after anaerobic digestion. The separated solids can be stored, composted or further processed into organic fertilisers. The liquid fraction is collected separately for subsequent use or treatment.

At livestock farms, the unit separates premixed liquid manure. Solids can be handled with a loader, while liquid can be pumped. Suitable sanitary treatment is required before using the solid fraction as bedding. The separator also handles suitable organic slurries from food processing.

Installation and maintenance

The support frame is offered separately. It positions the machine above the solids discharge area. Stairs provide maintenance access, and a roof protects the working platform from precipitation. A hot-dip galvanised frame is available for outdoor installations.

The control cabinet is offered separately. Its IP65 enclosure houses drive controls and protection against motor overload, phase supply faults and overheating. The cabinet is installed no more than 10 m from the machine. Access must be provided for cleaning, inspecting and replacing the screen and screw, together with unobstructed discharge of both fractions.

Technical characteristics
Features
Scope of supply

Version

Standard

Motor power

5.5 kW

Nominal throughput

25–45 m³/h

Dry matter in the solid fraction

25–30%

Screen diameter

261 mm

Screening section lengths

550 + 250 mm

Screen slot width

1.0 mm

Housing

Carbon steel

Internal components and screen

AISI 304 stainless steel

Separator dimensions, L × W × H

2335 × 910 × 1745 mm

Power supply

400 V / 50 Hz

Technical characteristics

Version

Standard

Motor power

5.5 kW

Nominal throughput

25–45 m³/h

Dry matter in the solid fraction

25–30%

Screen diameter

261 mm

Screening section lengths

550 + 250 mm

Screen slot width

1.0 mm

Housing

Carbon steel

Internal components and screen

AISI 304 stainless steel

Separator dimensions, L × W × H

2335 × 910 × 1745 mm

Power supply

400 V / 50 Hz

Features

550 + 250 mm screening sections with a 5.5 kW motor.

Dry matter in the separated solid fraction: 25–30%.

Dewatering adjustment using counterweighted arms.

Replaceable AISI 304 stainless-steel screen with 1.0 mm slots.

Scope of supply

Additional options

  • Support frame with stairs and roof, primer and protective paint.
  • IP65 control cabinet with motor overload, phase fault and overheating protection.
  • Hot-dip galvanising of the support frame.
  • Spare screens and wear-resistant screw coatings.

Price for the separator with geared motor, working screw and screen. The support frame and control cabinet are offered separately. Delivery, installation, commissioning, feed pump, external pipework and the main power line to the cabinet are not included.

ZSP-800 separator with a 5.5 kW geared motor and working screw.

AISI 304 screening elements: 550 + 250 mm, slot width 1.0 mm.

Outlet mechanism with adjusting arms and counterweights.

Other goods